Dynisco accessories
PPS1110 - Pressure calibrator
- Pressure range: 0 to 700 bar
- Accuracy: ± 0,1 % of the full pressure range
- Measurement interval: 0,5 seconds
- Medium: Oil
- CE compliant / RoHS compliant
PPS1210 - Pressure calibrator
- Pressure range 0-700 bar
- Pressure port 1/2"20UNF or M18x1.5 (other sizes available on request)
- Accuracy <0.05% FS
- Pressure display in 13 different units
- Battery-powered pressure display (mains power supply required for heating and for transferring data to a PC)
- Battery: standard commercially available button cell; Lifespan: >2000h of continual operation
- Data transfer to PC/laptop via USB interface; transfer cable included in delivery
- Oil volumes 57ml (HLP22BP/olive oil)
- Measurement interval 0.5 seconds
- Conforms with CE and RoHS
- DKD (Deutscher Kalibrierdienst / German Calibration Service) certification optional
- Environmental conditions: 0...50°C/5...95% relative humidity
- Dimensions (LxWxH): approx. 470 x 170 x 280 mm
- Weight: approx. 7.2 kg, with case approx. 13 kg
PPS1210L - Pressure calibrator
- Pressure range 0-700 bar
- Pressure port 1/2"20UNF or M18x1.5 (other sizes available on request)
- Accuracy <0.05% FS
- Pressure display in 13 different units
- Battery-powered pressure display (mains power supply required for heating and for transferring data to a PC)
- Battery: standard commercially available button cell; Lifespan: >2000h of continual operation
- Data transfer to PC/laptop via USB interface; transfer cable included in delivery
- Oil volumes 57ml (HLP22BP/olive oil)
- Measurement interval 0.5 seconds
- Conforms with CE and RoHS
- DKD (Deutscher Kalibrierdienst / German Calibration Service) certification optional
- Environmental conditions: 0...50°C/5...95% relative humidity
- Dimensions (LxWxH): approx. 470 x 170 x 280 mm
- Weight: approx. 7.2 kg, with case approx. 13 kg
VPC 999084 Transducer Simulator
- Selectable transducer output sensitivity
- Standard 6 pin Bendix connector
- 5 step linear output 0 – 100%
- Identifies faulty components in a measurement loop
Cleaning Set
The cleaning tool kit was designed by Dynisco for use in removing excess plastic from mounting holes for pressure and temperature transducers.
Installation of transducers into improperly cleaned or sized holes is one of the major causes of damage to these instruments. With this kit, the .312" tip
diameter hole, the 45 degree seating surface, and the .451" hole can be cleaned. The kit includes a gauging plug which is used to verify that the hole
has been correctly machined and cleaned. M10 and M18 cleaning kits also available.
Tool kit
The Transducer Mounting Hole Machining Tool Kit contains all of the necessary drills and taps to prepare a standard 1/2 - 20 UNF transducer mounting hole. The kit contains the special pilot drill required to machine the 45 degree seat. All tools included in this kit are made of premium grade, high strength tool steel. Care should be taken in the use of proper speeds and feeds, lubricants, and a method to assure continual alignment of each progressing tool. Consult Dynisco for additional or more specific information. M10 and M18 kits also available.
BP420 - upture Disks/Burst Plugs
- Welded one piece assembly - no degradation of joint strength at elevated temperatures
- Inconel rupture disk – stable through a wide range of temperatures
- Burst pressure ranges from 1,000 to 15,000psi
- Accuracy of ±10% of rated burst pressure at 300° – 750°F
- Designed for melt temperatures up to 800˚F (425˚C)
- Leak rate exceeds 1x10-6 standard cc/sec
