Dynisco Melt pressure transducers
Echo - Melt Pressure Sensors
- 2 year warranty and 60 years of Dynisco industry experience
- Accuracy better than ±0.5%
- TiAlN diaphragm coating is standard
- mV/V, 0-10VDC, or mA outputs available
- Integral temperature sensor option
- Available in configurations that fit most extruder applications
- 1.5M, 3M, 5M, 7.5M & 10M psi pressure range capability
Guardian - Pressure Sensors for Safety Assurance
- Integral relay switch for redundant safety and future compliance
- 3rd-party agency analysis (exida™) and self-certified based on FMEDA analysis and internal audit.
- Meets Performance Level ‘c’ as defined by the Machinery Directive (single sensor installed per Category 1).
- Meets Performance Level ‘d’ as defined by the Machinery Directive (two sensors installed per Category 3).
- Meets the following compliance directives, when properly installed and used:
- Machinery Directive 2006/42/EC
- NFPA 79 clauses A.9.2, A.9.4.1, A.9.4.3.2
- EMC Directive 2004/108/EC
- PED 97/23/EC
- Available on popular mV/V (PT, MDA, DYN) and mA-HART SPX models
MDA 420 / 460 - Melt pressure transducer for pressure measurement in hot media
- Installation for media temperature up to 400°C
- Rigid stem between diaphragm and housing
- Liquid-filled transmission system
- Electrical build-in calibration
- All stainless steel wetted parts
MDA 422 / 462 - Melt pressure transducer for pressure measurement in hot media
- Installation for media temperature up to 400°C
- Flexible capillary between rigid stem and housing
- Liquid-filled transmission system
- Electrical build-in calibration
MDA 435/467 - Melt pressure transducer for pressure measurement in hot media and small areas
- Installation for media temperature up to 400°C
- Pressure transducer for small areas
- Flexible capillary between diaphragm and housing
- Liquid-filled transmission system
- Electrical built-in calibration
- Exposed, bendable capillary
- Fits in space restricted areas
MDA 460M10 - Melt pressure transducer with mounting thread M10 x 1
- Diaphragm diameter 6 mm
- 40% smaller surface area vs. 1/2"-20 UNF-2A thread
- Suitable for smaller diameter of cylinders or pipes
- Accuracy 1.0%
- Temperature range up to 400°C
- Pressure ranges from 0-350 bar to 0-700 bar
PT462E - Massedruckaufnehmer
- Better than ±0.5% accuracy
- 3.33 mV/V FSO
- Internal 80% shunt calibration
- All stainless steel wetted parts
- 0 - 500 to 0 - 30,000 psi
- Good stability and repeatability
- Flexible stem
- Reliable pressure measurement
- Standard low level output
- Easy set - up
- Corrosion resistant
- Choice of pressure ranges
- Reliable measurement
- Easy to install and ideal for high local temperatures
PT460E - Melt pressure sensor
- Accuracy better than +/- 0.5%
- Dymax® coated stainless steel wetted parts
- Proven sensor design
- 0 - 500 to 0 -30,000 psi
- Internal 80% shunt calibration
- Reliable, repeatable pressure measurements
- Superior abrasion resistance
- Good stability and repeatability
- Wide variety of pressure ranges
- Easy to calibrate with local indicator
PT422 - Massedruckaufnehmer
- Installation for media temperature up to 400 °C
- Flexible capillary between rigid stem and housing
- Liquid-filled transmission system
- Electrical built-in calibration
PT462 - Massedruckaufnehmer
- Installation for media temperature up to 400 °C
- Flexible capillary between rigid stem and housing
- Liquid-filled transmission system
- Electrical built-in calibration
TPT463 - Melt pressure transducer
- Installation for media temperature up to 400 °C
- Integral thermocouple for simultaneous temperature measurement at the media
- Flexible capillary between rigid stem and housing
- Liquid-filled transmission system
- Electrical built-in calibration
TDA 432/463 - Melt pressure transducer for pressure and temperature measurement in hot media
- Installation for media temperature up to 400°C
- Integral thermocouple for simultaneus temperature measurement at the media
- Optional integral RTD element
- Flexible capillary between rigid stem and housing
- Liquid-filled transmission system
- Electrical built-in calibration
- Simultaneously measure pressure and temperature in one location
TPT4634 - Masseaufnehmer
- Better than ±0.5% accuracy
- 4 to 20 mA, 0 to 5 Vdc, 1 to 6 Vdc, 0 to10 Vdc, 1 to 11 Vdc outputs
- Stainless steel, Armoloy coated
- 0 - 500 to 0 - 30,000 psi
- Internal 80% shunt calibration
- Adjustable zero and span
- Integral thermocouple
- Reliable pressure measurement
- Direct input to supervisory control systems
- Minimizes thread galling, abrasion resistant
- Choice of pressure ranges
- Easy set-up >li>Adapt transmitter to process conditions
- Simultaneously measure pressure/temperature in one location
TPT4635 - Masseaufnehmer
- Better than ±0.5% accuracy
- 4 to 20 mA, 0 to 5 Vdc, 1 to 6 Vdc, 0 to10 Vdc, 1 to 11 Vdc outputs
- Stainless steel, Armoloy coated
- 0 - 500 to 0 - 30,000 psi
- Internal 80% shunt calibration
- Adjustable zero and span
- Integral thermocouple
- Reliable pressure measurement
- Direct input to supervisory control systems
- Minimizes thread galling, abrasion resistant
- Choice of pressure ranges
- Easy set-up
- Adapt transmitter to process conditions
- Simultaneously measure pressure/temperature in one location
TPT4636 - Masseaufnehmer
- Better than ±0.5% accuracy
- 4 to 20 mA, 0 to 5 Vdc, 1 to 6 Vdc, 0 to10 Vdc, 1 to 11 Vdc outputs
- Stainless steel, Armoloy coated
- 0 - 500 to 0 - 30,000 psi
- Internal 80% shunt calibration
- Adjustable zero and span
- Integral thermocouple
- Reliable pressure measurement
- Direct input to supervisory control systems
- Minimizes thread galling, abrasion resistant
- Choice of pressure ranges
- Easy set-up
- Adapt transmitter to process conditions
- Simultaneously measure pressure/temperature in one location